If you want to safely replace a worn-out electrical outlet, Beginnen Sie mit dem Ausschalten des Leistungsschalters, Dann abschrauben und die Steckdose abziehen, Streifen Sie die Enden der Drähte bei Bedarf neu ab >> Attach the new socket to the same three wires >> Screw the new socket in >> Turn on the breaker >>Test the socket with your fancy tester.
Guessing you are wondering how to safely replace a worn out electrical outlet? Wenn ja, you’ve found the right webpage.
It is also important to learn how to change a standard outlet to a GFCI outlet. Das Wechseln einer Standardsteckdose ist relativ einfach, aber achten Sie darauf, die folgenden Schritte zu befolgen. Sie sollten auch lernen, wie Sie eine GFCI-Steckdose sicher ersetzen. Diese Schritte können ohne professionelle Hilfe durchgeführt werden.
Ist es sicher, eine Steckdose zu wechseln??
Ja, Es ist sicher, eine Steckdose in Ihrem Haus auszutauschen. Vorsicht ist jedoch geboten. Es gibt mehrere Möglichkeiten, um festzustellen, ob eine Steckdose beschädigt ist. Zum Beispiel, es könnte funken oder flackern. Eine verschlissene Steckdose kann auch eine Brandgefahr darstellen. jedoch, this task does not have to be difficult if you follow a few precautions. Learn how to replace an outlet safely by following the guidelines below. You’ll need a pair of insulated gloves and a protective shield.
If you have an outlet with a screw terminal, you’ll need to unplug any devices that are plugged into it. In der Regel, outlets have screws on the sides. Typischerweise, the screws on the “hot” wire are brass and silver. The ground wire should be green. Before tightening the screws, make sure to cover the bare copper wire. Sobald die Schrauben gesichert sind, eine neue Steckdose einbauen.
Nächste, Trennen Sie den heißen Draht von der Steckdose. Sie sollten beim Umgang mit heißen Drähten immer vorsichtig sein, da die Gefahr eines Stromschlags hoch ist. Berühren Sie den heißen Draht niemals mit bloßen Händen. Verwenden Sie eine Zange mit Gummigriffen, um den Draht sicher zu berühren. Dabei, Achten Sie darauf, alle elektrischen Geräte und alle beschädigten Kabel aus der Steckdose zu entfernen, bevor Sie versuchen, sie auszutauschen. Dadurch wird verhindert, dass während des Austauschvorgangs eine potenzielle Gefahr entsteht.
DIY-Schritte zum Austauschen einer abgenutzten Steckdose
Wenn Ihre Steckdose abgenutzt ist und ersetzt werden muss, Es gibt einige einfache DIY-Schritte, mit denen Sie die Arbeit sicher und schnell selbst erledigen können.
Bevor es losgeht, Sie müssen sicher sein, dass Sie den richtigen Schaltplan für die Steckdose haben. Sie können ein Multimeter verwenden, um die Drähte zu bestimmen’ Spannung und identifizieren Sie, welche die ist “hot” eines. Ein Spannungsprüfer ist nützlich, wenn Sie eine defekte Steckdose ersetzen. Sie können auch das Erdungskabel überprüfen. Ein Erdungskabel ist schwarz. Dann, you can connect it to the green or silver screw. You must make sure to reconnect the wiring to prevent any electrical shocks.
- Zuerst, turn off the power feeding the outlet. If the power is still present, try plugging in a visible device into a different outlet to test the new one.
- If you see the lamp turning on or off, the outlet isn’t working correctly. To make sure you’ve inserted the new outlet correctly, try plugging a lamp into another outlet. If the lamp is still on, try re-plugging it.
- After removing the old outlet, carefully insert the new one. The old outlet was held on by the screws, so be careful not to over-tighten them. This can lead to a safety hazard.
- Once you have completed the process, you can easily move on to install the new outlet. Don’t forget to label the new one before you begin the process. A new outlet may include a label or diagrams that will help you do the job right.
How to replace a standard outlet with GFCI outlet
Before you can replace a worn-out electrical socket, Sie müssen zuerst den Strom zum alten ausschalten. Um die alte Steckdose zu testen, Schließen Sie ein offensichtliches Gerät an und schalten Sie den Leistungsschalter aus. Stellen Sie sicher, dass sich die Lampe nicht einschaltet. Wenn die Lampe tut, versuchen Sie, es an eine andere Steckdose anzuschließen. Wenn beide Lichter aus sind, Das bedeutet, dass die alte Steckdose nicht funktioniert.
Den FI-Ausgang erkennen Sie an seinen Schraubklemmen und der farblich gekennzeichneten Verdrahtung. Beim Neuverkabeln einer alten Steckdose, Achten Sie genau auf die Platzierung der Linienschrauben und Lastschrauben. Once you’ve made sure the GFCI outlet is installed correctly, screw in the faceplate and connect the power supply to it. Check that the outlet functions properly by plugging in a voltage tester.
If the GFCI outlet does not reset after detecting a faulty connection, it is possible that there are loose connections inside the socket. In order to check these loose connections, you can remove the old outlet and open the electrical box. Um dies zu tun, turn off all computers and the main circuit breaker. Nächste, bend some of the wires to see if they’re loose. You may notice that one of the wires is twisted and turned under a screw.